PureWax: Training Videos & Guides

Training Videos

 

PureWax Waterless Wash/Detailer

  1. Make sure to wash your vehicle in a shaded area and that the vehicle is cool to the touch.
  2. Shake well and spray directly on surface to be washed
  3. Wipe up the dirty solution in one direction with a clean microfiber towel. ( We recommend using the Purewax High Grade Microfiber towel)
  4. Buff the area dry with another clean microfiber towel to reveal a high gloss shine.
 

 

PureWax Final Touch

  1. Make sure your vehicle is in a shaded area and that the vehicle is cool to the touch, make sure it is cleaned with Car soap / Waterless wash

  2. Spray directly onto cool panels that have only light dust or fingerprint / smear contamination.

  3. Wipe up the dirty solution in one direction with a clean microfiber towel. ( We recommend using the Purewax High Grade Microfiber towel)

  4. Buff the area dry with another clean microfiber towel to reveal a high gloss shine.

     

     

    PureWax Edgeless Microfibre Cloths

    1. For a Scratch free finish- always use a clean side and wipe in straight horizontal or vertical lines only. Do Not do circular motion.
    2. Always keep a separate clean microfibre cloth for buffing only. Do Not buff with the same microfibre  towel which was used to clean dirt.

      

    PureWax Nanotech Wax / Sealant (Poxy)

    1. Shake well before use. Apply to a clean, dry surface.

    2. Can be applied by hand or machine. Do not over-apply this product as it will make buffing off more difficult and will not increase the shine or protection.

    3. Apply the thinnest coating possible to the whole car and allow product to bond to the surface for at least 15-20 minutes before buffing off with a clean, soft microfibre cloth.

    4. Product can be left on for up to 24 hours and will still buff cleanly off.

    5. For increased shine and durability, a second coat of PureWax Nanotech Wax / Sealant can be applied after 12 hours.

    PureWax Tyre Dressing / Conditioner

    1. Shake well and carefully spray product directly on surface to be treated OR Alternatively spray directly onto a cloth/applicator and apply.

    2. Depending on the level of shine required, allow the product to cure and remove excess with microfibre cloth.

    3. If you want a high shine simply allow curing for a few extra minutes

    4. If you want a low shine wipe off excess immediately after application.

    Purewax Leather and Waterless Combo

    1. Apply a small amount to a clean, damp cloth or applicator.

    2. Avoid applying directly onto surface.

    3. Using a circular motion, massage the product to leather or vinyl until the surface is fully covered.

    4. Buff off excess with a clean dry microfiber towel. Repeat as necessary.

    5. Do not use on suede, nubuck. (Always test in an inconspicuous area prior to treating entire panel)

    How to use Purewax Marine on a BBQ

    1. Shake bottle well to agitate formula.

    2. Spray a fine mist directly onto the surface to be cleaned. Using a clean slightly damp microfibre cloth, gently remove surface dirt and excess product in a linear motion.

    3. Use a second clean dry microfibre cloth to remove residue.

    4. Cleans and protects all surfaces.

    5. Use regularly to maintain a beautiful finish.


      Easy Bird Dropping Removal- Tips and Tricks

      How to use the Bugs and Tar spray-

      Remove stubborn Bugs and other Contamination.

      1. Spray directly on surface.

      2. Wipe bugs away using a premium microfiber towel.

      3. Rinse using clean water.

      4. Avoid using the product or leaving the active product on the vehicle in direct sunlight.

       

      How to Guide